| Last Modified: 11-29-2007 | 1.6 A | |
| Service Category: Vehicle Interior | Section: Heating/Air Conditioning | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM00000298Y00OX |
| Title: HEATING / AIR CONDITIONING: REAR AIR CONDITIONING UNIT: INSTALLATION (2008 Sequoia) | ||
INSTALLATION
1. INSTALL REAR COOLING UNIT ASSEMBLY
|
(a) Install the rear cooling unit with the 3 bolts and nut. Torque: 5.4 N·m (55 kgf·cm, 48 in·lbf) HINT:
Tighten the bolts in the order shown in the illustration. |
|
(b) Connect the 3 connectors. |
(c) Engage the 3 clamps.
2. INSTALL FOLD SEAT CONTROL ECU
3. INSTALL AMPLIFIER ANTENNA ASSEMBLY
|
(a) Install the amplifier antenna with the bolt. |
4. INSTALL REAR SIDE NO. 1 AIR DUCT
|
(a) Install the air duct with the clip. |
(b) Engage the clamp.
5. INSTALL COVER SUB-ASSEMBLY
|
(a) Engage the 2 claws and install the cover. |
6. INSTALL QUARTER TRIM BRACKET RH
|
(a) Install the quarter trim bracket with the 2 bolts. |
(b) Engage the clamp.
7. INSTALL REAR SIDE NO. 2 AIR DUCT
|
(a) Install the air duct with the 2 clips. |
8. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH
9. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Standard)
10. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)
11. INSTALL REAR FLOOR MAT SUPPORT PLATE
12. INSTALL ROPE HOOK ASSEMBLY
13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
14. INSTALL REAR DOOR SCUFF PLATE RH
15. INSTALL REAR FLOOR STEP NO. 1 COVER
16. INSTALL REAR FLOOR STEP NO. 2 COVER
17. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH
18. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)
19. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)
20. INSTALL SEAT TRACK BRACKET FRONT COVER INNER
21. INSTALL SEAT TRACK BRACKET FRONT COVER OUTER
22. INSTALL DECK BOARD BRACKET
23. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY
24. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY
25. INSTALL ROPE HOOK ASSEMBLY
26. INSTALL LUGGAGE COMPARTMENT TRIM BOX
27. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY
28. CONNECT COOLER REFRIGERANT LIQUID PIPE D
(a) Remove the attached vinyl tape from the pipe.
(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe.
Compressor oil:
ND-OIL 8 or equivalent
(c) Install the O-ring on the cooler refrigerant liquid pipe.
(d) Install the cooler refrigerant liquid pipe.
29. CONNECT COOLER REFRIGERANT SUCTION PIPE B
(a) Remove the attached vinyl tape from the pipe.
(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant suction pipe.
Compressor oil:
ND-OIL 8 or equivalent
(c) Install the O-ring on the cooler refrigerant suction pipe.
(d) Move the hook connector in the direction indicated by the arrow in the illustration.
|
(e) Insert the pipe joint into the fitting hole securely and tighten the bolt. Torque: 5.4 N·m (55 kgf·cm, 48 in·lbf) |
30. CONNECT HEATER WATER OUTLET HOSE E
|
(a) Connect the water hose onto the cooling unit. NOTICE:
Perform the installation with the hose clip and mark at the correct angle. |
31. CONNECT HEATER WATER INLET HOSE H
|
(a) Connect the water hose onto the cooling unit. NOTICE:
Perform the installation with the hose clip and mark at the correct angle. |
32. ADD ENGINE COOLANT (for 2UZ-FE)
33. ADD ENGINE COOLANT (for 3UR-FE)
34. INSPECT FOR COOLANT LEAK (for 2UZ-FE)
35. INSPECT FOR COOLANT LEAK (for 3UR-FE)
36. CHARGE REFRIGERANT
37. WARM UP ENGINE
38. INSPECT FOR REFRIGERANT LEAK
39. INSTALL ENGINE UNDER COVER NO.1
|
|